DBA 201 F 200 (8) mm (in.) | 440 W | 0.4 Ohm | Super Flat Sealed

High performance in a super flat design

The DBA 201 F flat active subwoofer enclosure optimized with FEM simulation ensures superior performance, maximizing the subwoofer output with a super flat size. The massive magnet of the 8 in. driver provides optimal control during the highest cone excursion.

Extra full set of controls to fine-tune the in-car performance

The built-in 24 dB/Oct. low-pass crossover filter with a variable cutting corner frequency (50÷150 Hz) allows you to perfectly match the DBA 201 F to your speaker system. Adjustable bass boost (0÷6 dB @ 45Hz) can add bass output as you prefer, allowing correction for OEM sound equalization. With the phase inverter (0-180°), you can optimize phase alignment between the DBA 201 F and your speaker system, regardless of the subwoofer’s position in the car. The subsonic filter (15 Hz @ 24 dB/Oct) protects the cone from over-excursion and amplifiers from overheating. The input sensitivity control is the perfect tool to maximize the overall system output level while preventing clipping.

Auto turn-on and standby mode

The built-in audio sense circuit allows the DBA 201 F to turn on and timeout to standby mode automatically. You can switch off the audio sense function when a remote turn-on wire is available.
Size mm (in.) 200 (8)
Power Handling - Continuous W 220
Power Handling - Peak W 440
Impedance Ohm 0.4
Design Super Flat Sealed
Voice Coil Ø 38.6 (1.52) mm (in.)
Frequency Response Hz 32 ÷ 400
Magnet size D x d x h mm (in.) 110 x 45 x 17 (4.33 x 1.78 x 0.67)
Weight of one component kg (lb.) 4.3 (9.48)
Magnet High Density Flux Ferrite
Cone Pressed paper
Voice Coil Type Copper
Technical Specs
Operating voltage VDC (Fuse) 6.5 ÷ 18 (15A)
Start - Stop voltage VDC 6
Idling current A (Power OFF) 260 m (1 m)
Consumption @ 14,4 VDC Max musical power A 8.5
Remote IN Turn on VDC (Current) 4 (1 mA)
PRE input signal Turn ON VRMS 10 mV
SPK input DC Turn ON VDC 2
Power Supply
Distortion - THD @ 100 Hz % 0.15
Bandwidth Hz 15 - 150
S/N ratio dBA 100
Output power (RMS) @ 14,4 VDC, 1% THD W 220
Amplifier Stage
PRE input signal VRMS (impedance) 0.2 ÷ 5 (10kΩ)
SPK input signal VRMS (impedance) 1.2 ÷ 30 (6Ω)
LO-PASS Filter @ 24 dB Oct adjustable Hz 50 ÷ 150
Subsonic Filter @ 24 dB Oct Fixed Hz 15
Phase switch 0 / 180°
Bass Boost @45 Hz dB 0 ÷ 6
Sub remote volume control dB 0 ÷ -15 (HRC 01 included)
Signals Inputs / Filter
Physical Specs
DBA 201 F
mm in
A 345 13.58
B 245 9.64
C 79 3.11
Accessories
DBA 201 F
HRC 01
Provided remote-control

DBA 201 F level can be adjusted (-15 dB ÷ 0 dB) using the new stylish HRC 01 remote control. HRC 01 AS control is ready for tape surface mounting, screw surface mounting, and recessed mounting, thanks to the provided accessories.

Features
DBA 201 F
  • High performance in a super flat design
  • Internal 440-watt peak Class D amplifier
  • Compatible with every car audio system
  • Plug & Play connection
  • Extra full set of controls to fine-tune the in-car performance
  • Auto turn-on and standby mode
  • Provided remote-level control
Technologies
DBA 201 F

 

The 440 W Class D amplifier provides an unmatched performance/size ratio, drawing less current from the vehicle’s electrical system. He-Li technology (high efficiency/low impedance) is optimized for the 0.4 Ω load of the DBA 201 subwoofer driver, and the sealed enclosure.

DBA 201 F

 

DBA 201 F can handle speaker-level signals up to 30 volts (1.2V – 30 V rms) and includes USS for OEM systems and handles RCA line-level signals as well (0.2mV – 5 V rms) from aftermarket systems. Thanks to the low idling current and wide operating supply voltage (6.5V – 18V) DBA 201 F is fully EV (Electrical Vehicle) friendly.

DBA 201 F

 

The DBA 201 F flat active subwoofer enclosure optimized with FEM simulation ensures superior performance, maximizing the subwoofer output with a super flat size. The massive magnet of the 8 in. driver provides optimal control during the highest cone excursion.

DBA 201 F

 

The DBA 201 F is designed to easily release via a Plug & Play Molex® and harness, which includes the power connection. When you need extra cargo room, you can quickly unplug and remove the box.